PRODUCTS

NICHROME

FECRAL

NICHROME WITH INSULATION

TITANIUM

TUNGSTEN

MOLYBDENUM

COBALT

THERMOCOUPLES

HEAT-RESISTING THERMOCOUPLES

NICKEL

MONEL

CONSTANTAN

CUPRONICKEL

HARD ALLOYS

METAL POWDERS

STAINLESS STEEL

HEAT-RESISTANT ALLOYS

FERROALLOYS

TIN

TANTALUM

NIOBIUM

VANADIUM

CHROMIUM

RHENIUM

PRECISION ALLOYS

ZIRCONIUM


 
Attention! If you found an error on the site please select it and press Ctrl + Enter.

 

+7 (495) 366-00-24 logo
+7 (495) 366-00-24
e-mail: metoteh@gmail.com

Vanadium wire and filament

Calculate the mass of vanadium products

Calculator "Metals and alloys". Vanadium


Wire Tube Rod Tape Strip Sheet Hexahedron Corner Rectangle

Help

Result:
Result:

Density: g/cm³
Thickness, mm
Side 1, mm
Side 2, mm
Width, mm
Ø, mm
Wall, mm
Length
Weight

R E S E T


Vanadium is mainly in demand in metallurgical production in the form of ingots, powder or ferroalloy. However, round section rolling is also produced and finds practical application. An example is the electronic industry and scientific activities.

You can buy vanadium wire and filament in the company Metotechnics. Our company offers a wide range of products. To order, you can use email, phone or a special form on the page with prices.

More information about the products made of vanadium of round section and small diameter, its characteristics, production, application and grades, is presented on this page in appropriate sections.

Grades

Vanadium wire and filament are produced under the grades VnPr-1 and VnPr-2. The chemical composition of these materials is similar to those used in production of vanadium rods.

It is based on the chemical element V. Its mass fraction is 99.38% and 99.04%, accordingly. Since the products are made from pure vanadium, the mass fraction of impurities is insignificant and ranges from thousandths to tenths of a percent: silicon (Si), aluminum (Al) - 0.2/0.3%; iron (Fe) - 0.15/0.25%; oxygen (O) - 0.03/0.05%; carbon (C) - 0.03/0.04%; nitrogen (N) - 0.01/0.02%; hydrogen (H) - 0.001/0.001%.

The chemical composition of the grades VnPr-1 and VnPr-2 is presented in the TC 48-4-372-76.

Production

Vanadium filament and wire are made from cylindrical ingots that meet the requirements of the TC 48-4-272-73. These workpieces are subjected to repeated pressure treatment. As a result of deformation, the diameter of semi-finished products gradually decreases, eventually reaching small sizes (no more than a few millimeters).

The products are delivered in annealed or autofrettaged form. Among the sizes, the diameter is controlled. Its maximum deviations of hundredths of a millimeter and the minimum length are regulated. For semi-finished products with diameter Ø 0.5-1.0 mm inclusive, the minimum length is 3 m. Such products are usually supplied on coils. Vanadium filament and wire with diameter Ø 1.0-3.0 mm inclusive are supplied in bays of a minimum length of 2 m.s

The main technological parameters of the considered products, including sizes, delivery status, packaging and transportation rules, are presented in the TC 48-4-372-76.

Application

The considered products are used in the production of electronics because of their small sizes. They are also used in scientific experiments.

Prices

The price of vanadium wire and filament, the range of products and their availability are presented on the Cost page. There you can also order products through the website.

"Metotechnics"
e-mail: metoteh@gmail.com

Tel:
+7 (495) 366-00-24

Nichrome :: Fecral :: Nichrome with insulation :: Titanium :: Tungsten :: Molybdenum :: Cobalt :: Thermocouples :: Heat-resisting thermocouples :: Nickel :: Monel :: Constantan :: Cupronickel :: Hard alloys :: Metal powders :: Stainless steel :: Heat-resistant alloys :: Ferroalloys :: Tin :: Tantalum :: Niobium :: Vanadium :: Chromium :: Rhenium :: Precision alloys :: Zirconium