PRODUCTS

NICHROME

FECRAL

NICHROME WITH INSULATION

TITANIUM

TUNGSTEN

MOLYBDENUM

COBALT

THERMOCOUPLES

HEAT-RESISTING THERMOCOUPLES

NICKEL

MONEL

CONSTANTAN

CUPRONICKEL

HARD ALLOYS

METAL POWDERS

STAINLESS STEEL

HEAT-RESISTANT ALLOYS

FERROALLOYS

TIN

TANTALUM

NIOBIUM

VANADIUM

CHROMIUM

RHENIUM

PRECISION ALLOYS

ZIRCONIUM


 
Attention! If you found an error on the site please select it and press Ctrl + Enter.

 

+7 (495) 366-00-24 logo
+7 (495) 366-00-24
e-mail: metoteh@gmail.com

Monel strip and foil

Calculate the mass of monel products

Calculator "Metals and alloys". Monel


Wire Tube Rod Tape Strip Sheet Hexahedron Corner Rectangle

Help

Result:
Result:

Density: g/cm³
Thickness, mm
Side 1, mm
Side 2, mm
Width, mm
Ø, mm
Wall, mm
Length
Weight

R E S E T


The combination of a small thickness of the described semi-finished products with excellent corrosion resistance of monel metal makes it possible to produce small sized parts, but at the same time resistant to aggressive substances.

In the company Metotechnics you can buy monel strip and foil. Just call the phone, send a request by email, or make an order via the website on the page with the price list.

You can learn more information about corrosion-resistant alloys, their production methods and application areas on this page in the appropriate sections.

Grades

The strip and foil are made from alloys NiCuFeMn 28-2, 5-1, 5 and Monel 400, 401, 404, R-405, K-500.

The main components of these grades are nickel + cobalt (Ni + Co) and cuprum(Cu). Monel 400 contains at least 63% of Ni, 28-34% of Cu, and 28-2,5-1,5 NiCuFeMn 28-2,5-1,5 - at least 65.8% and 27-29% accordingly. These alloys also contain manganese (Mn), ferrum (Fe) and some impurities: carbon (C), magnesium (Mg), phosphorus (P), silicon (Si) and others.

The chemical composition of NiCuFeMn 28-2, 5-1, 5 is regulated by GOST 492-2006. Monel 400 is regulated by the standards of Special Metals Corporation (USA), which owns the rights to the MONEL trademark.

Production

Monel foil and strip are produced by rolling. This technological operation is carried out without heating, so the products are obtained cold-formed.

After rolling, the workpieces are subjected to thermal and mechanical processing - they are annealed, cut and trimmed edges. Heat treatment allows to get soft or semi-hard products, and mechanical treatment allows to get required length and width.

Monel foil is a strip that has a small thickness, usually less than 0.1 mm.

Sizes of products from alloy NiCuFeMn 28-2,5-1,5, the delivery status and mechanical properties are regulated by the standard GOST 5187-2003; from alloy Monel 400 - by standards of the company Special Metals Corporation (USA), which has the rights to the trademark MONEL.

Application

Monel strip and foil are used as construction material for marine vessels, equipment for the chemical and oil refining industries, valves, pumps, shafts, fittings, fasteners and heat exchangers. This application is related to high corrosion resistance of the alloy in sea and fresh water, as well as in some acids and alkalis.

Prices

The Cost page presents prices for monel foil and strip and other characteristics of products available for order.

"Metotechnics"
e-mail: metoteh@gmail.com

Tel:
+7 (495) 366-00-24

Nichrome :: Fecral :: Nichrome with insulation :: Titanium :: Tungsten :: Molybdenum :: Cobalt :: Thermocouples :: Heat-resisting thermocouples :: Nickel :: Monel :: Constantan :: Cupronickel :: Hard alloys :: Metal powders :: Stainless steel :: Heat-resistant alloys :: Ferroalloys :: Tin :: Tantalum :: Niobium :: Vanadium :: Chromium :: Rhenium :: Precision alloys :: Zirconium